In mid-April a woman from the marketing department ofÂ No Starch Press contacted me and asked if I am interested to do a public review of the FreeBSD Device Drivers bookÂ by Joseph Kong (no link to a book shop, go and have a look in your preferred one). Just this simple question, no strings attached.
I had my nose in some device drivers in the past, but I never wrote one, and never had a look at the big picture. I was interested to know how everything fits together, so this made me a good victim for a review (novice enough to learn something new and to have a look if enough is explained,Â and experienced enough to understand what is going on in the FreeBSD kernel).
Some minutes after I agreed to review it (but with a little notice that I do not know how long I need to review it), I had the PDF version of the book. That was faster than I expected (maybe I am too old-school and used to have paper versions of books in my hands).
Let the review beginâ€¦ but bear with me, this is the first time I do a real public review of a book (instead of a technical review for an author). And as this is my very own personal opinion, I will not allow comments here. This page is all about my opinion while reading the book, questions I have while reading the book shall serve as a hint about the quality of the book and they should be answered in the book, not here.
In short, the book is not perfect, but it is a good book. There is room for improvement, but on a very high level. If you want to write a device driver for FreeBSD, this book is a must. I suggest to read it completely, even chapters which do not belong to the type of driver you want to write (specially the case studies of real drivers). The reason is that each chapter has some notes whichÂ may not only apply to the chapter in question, but to all kinds of device drivers. The long review follows now.
The first chapter is titled â€œBuilding and running modulesâ€?. The author begins with description of the usual device driver types (NIC driver, pseudo-device, â€¦)Â and how they can be added to the kernel (statically linked in or as a module). The first code example is aÂ small and easyÂ kernel module, so that we do not have to reboot the system we use to develop a driver (except we make a fault during driver development which causes the machine to panic or hang). Every part of the exampleÂ is well explained. This is followed by an overview about character devices (e.g. disks)Â and a simple character-device driver (so far a pseudo-device, as we do not have real hardware we access) which is not only as-well explained as the module-example, but there is also a note where the code was simplified and what should be done instead.
After reading this chapter you should be able to write your own kernel module in 5 minutes (well, after 5 minutes it will not be able to do a lot â€” just a â€œhello worldâ€? â€“Â but at least you can alreadyÂ load/unload/execute some code into/from/in the kernel).
I have not tried any example myself, but I compiled a lot of modules and drivers I modified in the past and remember to have seen the described parts.
The second chapter explains how to allocate and freeÂ memory in the kernel. There is the possibility to allocate maybe-contiguous memory (the normal case, when your hardware does not do DMAÂ or does not have the requirement that the memory region it makes DMA from/too needs to be contiguous), and really contiguous. For the size argument of the freeing of the the contiguous memory there is the sentence â€œGenerally, size should be equal the amount allocated.â€?.Â Immediately I wanted to know what happens if you specify a different size (as a non-native english speaker I understand this sentence in a way that I am allowed to specify a different size and as such are able to freeÂ only partsÂ of the allocated memory). Unfortunately this is not answered. I had a look into the source, the kernel frees memory pages, so the size argument (and addr argument)Â will be rounded toÂ include a fullÂ page. This means theoretically I am able to freeÂ parts of the allocated memory, but this is a source-maintenance nightmare (needs knowledge about the machine specific page boundaries and you need to make sure that you do the absolutely correct size calculations).Â To me this looks more like as long as nobody is pointing a gun at my head and tells me to use a different size, specifying the same size as made during the allocation of this memory region is the way to go.
After reading this chapter you should know how toÂ killÂ theÂ system by allocating all the RAM in the kernel.
Again, I did not try to compile the examples in this chapter, but the difference of the memory allocation in the kernel compared with memory allocation in the userland is not that big.
The third chapter explains the device communication and control interfaces (ioctl/sysctl)Â of a driver. The ioctl part teached me some parts IÂ always wanted to know when I touched some ioctls, but never bothered to find out before. Unfortunately this makes me a little bit nervous about the way ioctls are handled in the FreeBSD linuxulator, but this is not urgent ATM (and can probably be handled by a commend in the right place). The sysctl part takes a little bit longer to follow through, but there is also more to learn about it. If you just modify an existing driver with an existing sysctl interface, it probably just comes down to copy&paste with little modifications, but if you need to make more complex changes or want to add a sysctl interface to a driver, this part of the book is a good way to understand what is possible and how everything fits together. Personally I would have wished for a more detailed guide when to pick the ioctl interface and when the sysctl interface than what was written in the conclusion of the chapter, but it is probably not that easy to come up with a good list which fits most drivers.
After reading this chapter you should be able to get data in and out of the kernel in 10 minutes.
As before, I did not compile the examples in this chapter. I already added ioctls and sysctls in various places in the FreeBSD kernel.
Chapter 4 is about thread synchronization â€“Â mutexes, shared/exclusive locks, reader/writer locks and condition variables. For me this chapter is not as good as the previous ones. While I got a good explanation of everything, I missed a nice overview table which compares the various methods of thread synchronization. Brendan Gregg did a nice table to give an overview of DTrace variable typesÂ and when to use them. Something like this would have been nice in this chapter too. Apart from this I got all the info I need (but hey, I already wrote a NFS client for an experimental computer with more than 200000 CPUs in 1998, so Iâ€™m familiar with such synchronization primitives).
Delayed execution is explained in chapter 5. Most of the information presented there was new to me. While there where not much examples presented (there will be some in a later chapter), I got a good overview about what exists.Â This time there was even an overview when to use which type of delayed execution infrastructure.Â I would have preferred to have this overview in the beginning of the chapter, but that is maybe some kind of personal preference.
In chapter 6 a complete device driver is dissected. It is the virtual null modemÂ terminal driver.Â The chapterÂ provides real-world examples of event-handlers, callouts and taskqueues which where not demonstrated in chapter five. At the same time the chapter serves as a description of the functions a TTY driver needs to have.
Automated device detection with Newbus and the corresponding resource allocation (I/O ports, device memory and interrupts)Â are explained in chapter 7. It is easyâ€¦ if you have a real device to play with. Unfortunately the chapterÂ missed aÂ paragraph or twoÂ about the suspend and resume methods. If you think about it, it is not hard to come up with what they are supposed to do, but a little explicit description of what they shall do, in what state the hardware should be put and what to assume when being called would have been nice.
Chapter 8 is about interrupts. It is easy to add an interrupt handler (or to remove one), the hard part is to generate an interrupt. The example code uses the parallel port, and theÂ chapter also contains a little explanation how to generate an interruptâ€¦ if you are not afraid to touch real hardware (the parallel port)Â with a resistor.
In chapter 9 the lpt(4) driver is explained, as most of the topics discussed so far are used inside. The explanation how everything is used is good, but what I miss sometimes is why they are used. The most prominent (and only) example here for meÂ is why are callouts used to catch stray interrupts? That callouts areÂ a good way of handling thisÂ is clear to me, the big question is why can there be stray interrupts. Can this happen only for the parallel port (respectively a limited amount of devices), or does every driver for real interrupt driven hardware need to come with something like this? I assume this is something specific to the device, but a little explanation regarding this would have been nice.
Accessing I/O ports and I/O memory for devices are explained in chapter 10 based upon a driver for a LED device (turn on and off 2 LEDs on an ISA bus). All the functions to read and write data are well explained, just the part about the memory barrier is a little bit short. It is not clear why the CPU reordering of memory accesses matter to what looks like function calls. Those function calls may be macros, but this is not explained in the text. Some little examples when to use the barriers instead of an abstract description would also have been nice at this point.
Chapter 11 is similar to chapter 10, just that a PCI busÂ driver is discussed instead of an ISA bus driver. The differences are not that big, but important.
In chapter 12 it is explained how to do DMA in a driver. This part is not easy to understand. I would have wanted to have more examples and explanations of the DMA tag and DMA map parts. I am also surprised to see differentÂ supported architecturesÂ for the flags BUS_DMA_COHERENT and BUS_DMA_NOCACHE for different functions. Either this means FreeBSD is not coherent in those parts, or it is a bug in the book, or it is supposed to be like this and the reasons are not explained in the book. As there is no explicit note about this, it probably leads to confusion of readers which pay enough attention here.Â It would also have been nice to have an explanation when to use those flags which are only implemented on a subset of the architectures FreeBSD supports. Anyway, the explanations give enough information to understand what is going on and to be able to have a look at other device drivers for real-live examples and to get a deeper understanding of this topic.
Disk drivers and block I/O (bio) requests are described in chapter 13. With this chapter I have a little problem. The author used the word â€œundefinedâ€? in several places where I as a non-native speaker would have used â€œnot setâ€? or â€œset to 0â€³. The word â€œundefinedâ€? implies for me that there may be garbage inside, whereas from a technical point of view I can not imagine that some random value in those places would have the desired result. In my opinion each such place is obvious, so I do not expect that an experienced programmer would lose time/hairs/sanity over it, but inexperienced programmers which try to assemble the corresponding structures on the (uninitialized) heap (for whatever reason), may struggle with this.
Chapter 14 is about the CAM layer. While the previous chapter showed how to write a driver for a disk device, chapter 14 gave an overview about how to an HBA to the CAM layer. It is just an overview, it looks like CAM needs a book on its own to be fully described. The simple (and most important) cases are described,Â with the hardware-specific parts being an exercise for the person writing the device driver. I have the impression it gives enough details to let someone with hardware (or protocol), and more importantly documentation for this device, start writing a driver.
It would have been nice if chapter 13 and 14 would have had a little schematic which describes at which level of the kernel-subsystems the corresponding driver sits. And while I am at it, a schematic with all the driver components discussed in this book at the beginning as an overview, or in the end as an annex, would be great too.
An overview of USB drivers is given in chapter 15 with the USB printer driver as an example for the explanation of the USB driver interfaces. If USB would not be as complex as it is, it would be a nice chapter to start driver-writing experiments (due to the availability of various USB devices). Wellâ€¦ bad luck for curious people. BTW, the author gives pointers to the official USB docs, so if you are really curious, feel free to go ahead.
Chapter 16 is the first part about network drivers. It deals with ifnet (e.g. stuff needed for ifconfig), ifmedia (simplified: which kind of cable and speed is supported), mbufs and MSI(-X). As in other chapters before, a little overview and a little picture in the beginning would have been nice.
Finally, in chapter 17, the packet reception and transmission of network drivers is described. Large example code is broken up into several pieces here, for more easy discussion of related information.
One thing I miss after reaching the end of the book is a discussion of sound drivers. And this is surely not the only type of drivers which is not discussed, I can come up with crypto, firewire, gpio, watchdog, smb and iic devices within a few seconds. While I think that it is much more easy to understand all those drivers now after reading the book, it would have been nice to have at least a little overview of other driver types and maybe even a short description of their driver methods.
Conclusion: As I wrote already in the beginning, the book is not perfect, but it is good. While I have not written a device driver for FreeBSD, the book provided enough insight to be able to write oneÂ and to understand existing drivers. I really hope there will be a second edition which addresses the minor issues I had while reading it to make it a perfect book.